Sales Hotline: +44 (0)1492 541300

British Military Swords

Items 1 to 10 of 17 total

Set Descending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2
  • Excl. Tax: £187.50 Incl. Tax: £225.00

  • British Infantry Officer's Sword - ER 1897 Pattern (Steel Scabbard)

    This sword is considered by some to be the best fighting sword ever issued to a British Officer. As such it has never been replaced and is the current issue sword within the British Army. The only difference between this sword and its Victorian predecessor is the cypher of the reigning monarch at the time of issue. The polished blade has been forged from AISI 1065 High Carbon Steel and has been well tempered.

    Scabbard included. Replacement steel scabbard and leather scabbard available separately.

    Total length: 98 cm
    Blade length: 82.5 cm
    Grip length:  10.5 cm
    Weight: 0.902 kg
    Blade thickness (base): 5.6 mm
    Blade thickness (CoP): 4.7  mm
    Blade width (base):  2.3 cm
    Blade width (CoP): 2 cm 
    Point of Balance (PoB): 14 cm
    Centre of Percussion (CoP):  26 cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Steel

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £187.50 Incl. Tax: £225.00

  • British Artillery Officer's Sword - 1821 Pattern

    This replica of a 19th Century Royal Artillery Officer’s Sword has an embossed, unsharpened blade of AISI1065 High Carbon Steel . The hilt is of steel and the grip is wrapped with brown leather and inlaid with bands of twisted wire. The wooden scabbard wrapped with brown leather is in the ‘’Sam Browne’’ style, which became standard issue in the Boer War and into WWI. It has a steel throat piece, and an integrated, leather strap with a hole for a hanging pin.

    Total length:  106cm
    Blade length:  90cm
    Grip length:   11.7cm
    Weight:  906g
    Blade thickness (base): 0.6cm 
    Blade width (base):   2.5cm
    Blade: AISI 1065 High Carbon Steel 
    Edge: Blunt
    Pommel: Nut
    Scabbard: Leather, Wood, Steel

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £165.83 Incl. Tax: £199.00

  • British Cavalry Officer Sword - 1908 Pattern

    The 1908 Pattern Cavalry Trooper's Sword was the last service sword issued to the cavalry of the British Army. It is widely considered the most effective cavalry sword ever designed, although ironically its introduction occurred as swords finally became obsolete as military weapons. This sword has a forged steel blade which has not been tempered so we would only recommend it for display only. Steel guard, wood grip and steel scabbard (painted green).

    Total length: 110 cm
    Blade length: 89 cm
    Grip length: 12 cm
    Weight: 1400 g
    Blade thickness (base): 0.97 cm
    Blade width (base):  2.7 cm
    Point of Balance (PoB): 7 cm
    Blade: EN9 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Steel

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £74.17 Incl. Tax: £89.00

  • British Household Cavalry Sword - 1834 Pattern

    After the Crimean War there were many changes made within British Heavy Cavalry Regiments. One of these changes was the adoption of a variation of the 1st Life Guards Sword by the 2nd Life Guards. This sword served throughout the Boer War and WWI until the regiments were amalgamated in 1922. It still serves today as the official state sword of the Life Guards. The polished blade has been forged from EN9 steel and has been well tempered.

    Total length:
     116 cm
    Blade length: 99.5 cm
    Grip length:  11 cm
    Weight: 1.202 kg
    Blade thickness (base):  7.4 mm
    Blade thickness (CoP): 5.5 mm
    Blade width (base):  3 cm
    Blade width (CoP): 2.5 cm
    Point of Balance (PoB):  21 cm
    Centre of Percussion (CoP):  30 cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Peened
    Scabbard: Steel, Brass

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £165.83 Incl. Tax: £199.00

  • British Infantry Officer's Sword - 1796 Pattern

    This replica of the 1796 British Infantry Officer sword has a blade of unsharpened, tempered high carbon steel. Both sides of the blade feature the embossed cyper of the British Crown surmounted extensively by royal devices and floral motifs. It has a hilt of brass and a grip wrapped in copper wire that is plated with silver. Half of the guard is hinged and folds for ease of carry at the hip. The scabbard is of leather with brass accents.

    Total length: 95cm

    Blade length: 80cm
    Grip length: 6.5cm
    Weight: 784g
    Blade thickness (base): 0.7cm 
    Blade width (base): 2.5cm
    Point of Balance (PoB): 31cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Leather, Wood, Brass

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £187.50 Incl. Tax: £225.00

  • British Infantry Officer's Sword - 1796 Pattern

    When the British Army standardized the swords to be carried by infantry officers in 1796 this is the sword they settled on; a spadroon-like cut-and-thrust sword with simple, but elegant Georgian styling that hearkened back to the Smallswords carried by gentlemen in earlier times. In just four years following, the blade was at the hip of practically all British Line Infantry Officers. Regardless of the standardization of form, the blades varied in their width and in their engraved decoration. Though widespread, it was not regarded as a good combat blade despite being used through the entirety of Britain’s contests with France in the Napoleonic Era. It would not be officially replaced until 1822 by the more elaborate ‘’Gothic-Hilted’’ sword and before then many officers had opted to acquire the 1803 Pattern sabre instead.

    Total length: 100cm
    Blade length: 85cm
    Grip length: 6cm
    Guard width: 9.5cm
    Weight: 946g
    Blade thickness (base): 0.6cm
    Blade width (base): 2.5cm
    Point of Balance (PoB): 33cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Leather, Wood, Brass

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £208.33 Incl. Tax: £250.00

  • British Sergeant Sword - 1796 Pattern

    This recreation of the British 1796 Sergeant’s sword has a plain blade of unsharpened, tempered, high carbon steel. The hilt is entirely of brass. The scabbard is of leather with brass accents. The sword is the longer version used by the sergeants instead of the shorter blade used by the musicians, though the overall sword design and construction were inherently the same.

    Total length: 95cm
    Blade length: 80cm
    Grip length: 9cm
    Weight: 882g
    Blade thickness (base): 0.6cm 
    Blade width (base): 2.5cm
    Point of Balance (PoB): 32cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Leather, Wood, Brass

    All dimensions are approximate and may vary from piece to piece

    Learn More
    Excl. Tax: £187.50 Incl. Tax: £225.00

  • Highland Officer’s Sword - 1828 Pattern

    The 1828 Pattern Highland Officer’s Sword was issued to Officers of Scottish Highland Regiments such as the 92nd Regiment of Foot – The Gordon Highlanders. It was carried throughout many campaigns throughout the 19th Century and even saw service in WWI. Sergeants of such regiments were often issued with a plain bladed version.

    Our 1828 Pattern Highland Officer’s Sword is handcrafted like the originals and features a forged and tempered AISI1065 High Carbon Steel blade. The steel hilt features a red cloth liner, brown leather grip and red pommel tassel. The etched blade is housed in an authentically styled steel scabbard. 

    Total length: 100 cm
    Blade length: 81 cm
    Grip length: 13 cm
    Weight: 1.360 kg
    Blade thickness (base): 6.8 mm
    Blade thickness (CoP): 5 mm
    Blade width (base): 2.6 cm
    Blade width (CoP): 2.5 cm
    Point of Balance (PoB): 9 cm
    Centre of Percussion (CoP): 25 cm
    Blade: AISI1065 High Carbon Steel
    Edge: Blunt
    Pommel: Nut
    Scabbard: Steel

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £193.33 Incl. Tax: £232.00

  • British Royal Navy Officer's Sword - 1805 Pattern

    1 Review(s)

    Up until 1805 the Royal Navy did not have a regulation pattern sword. The sword that was introduced was modelled on the 1803 pattern infantry sabre that was previously carried by Navy and Marine officers. The 1805 pattern sword was used by Lord Horatio Nelson and he was no doubt armed with it at his most famous battle, The Battle of Trafalgar. After he was killed at the battle his sword was returned to England and is now on display in the Nelson Museum, Great Yarmouth, England. This sword was in constant use until it was replaced in 1827 by a newer model. The polished blade has been forged from AISI 1065 High Carbon Steel and has been well tempered.

    Total length: 95 cm
    Blade length: 83 cm
    Grip length: 10 cm
    Weight: 0.905 kg
    Blade thickness (base): 7.8 mm
    Blade thickness (CoP): 5.3 mm
    Blade width (base): 2.6 cm
    Blade width (CoP): 2.2 cm
    Point of Balance (PoB): 18 cm
    Centre of Percussion (CoP): 25 cm
    Blade: AISI 1065 High Carbon Steel
    Edge: Blunt
    Pommel: Peened
    Scabbard: Leather, Wood, Brass

    All dimensions are approximate and may vary from piece to piece.

    Learn More
    Excl. Tax: £165.83 Incl. Tax: £199.00

Items 1 to 10 of 17 total

Set Descending Direction
per page

Grid  List 

Page:
  1. 1
  2. 2
Registered Company number. 6769534 (England and Wales) UK Vat Number: 779 5190 76